Driver guide

What Is an Arrival Wave, and How Drivers Can Use It

An arrival wave is a stretch of time, often about an hour, when many more flights and travelers land at an airport than usual for that hour. For a driver, a wave is the moment when an airport goes from quiet to busy, and then back again. Whether you drive rideshare or a taxi, or work as a chauffeur, knowing when a wave is coming helps you be in the right place at the right time instead of guessing.

This explainer covers what a wave is, why waves happen, how PeakMere spots them, how to turn a wave into curb time, why big connecting hubs behave differently, and a simple playbook you can use on your next airport shift.

What an arrival wave is

Think of an airport's day as a series of tides. Some hours are steady, some are slow, and some bring a surge of flights landing within a short window. A wave is one of those surges: noticeably more arrivals than normal for that time of day, packed close together.

Some waves are part of the normal daily rhythm and show up day after day. Others are unusual: they appear because something changed that day, such as delays bunching flights together. Both matter to you, but the unusual ones are the ones you cannot plan for from a weekly pattern alone.

To get a feel for scale, here are typical-day estimates from our data. At Atlanta (ATL), about 10,500 travelers land from 8 AM to 9 AM on a typical day, out of about 137,500 for the whole day. At Denver (DEN), about 9,000 travelers land from 8 AM to 9 AM and about 8,800 from 4 PM to 5 PM. These are the airports' regular busy hours, local time. A wave on top of that, or in an hour that is usually calmer, can change how long you wait at the curb.

Why waves happen

There are two common reasons.

Scheduled banks at hub airports. Large connecting hubs often schedule flights in groups, sometimes called banks. Many flights land close together, travelers change planes, and then many flights leave close together. This lines up connections, and it creates regular waves that repeat on most days, give or take a little.

Delays that bunch flights together. When flights run late, they often end up landing at the same time. Common triggers include:

  • Bad weather at the airport or along the route
  • A ground stop, when flights headed to the airport are held at their departure airports for a while
  • A slow start in the morning that pushes later flights back

When a ground stop ends, the held flights tend to depart at about the same time and then land at about the same time, roughly one flight time later. That can turn a quiet stretch into a sudden wave.

Waves shift with seasons, holidays and weather, and they can grow or shrink during the day as delays build or clear.

How PeakMere spots a wave

PeakMere looks ahead from about 30 minutes to 3 hours. It checks each 60-minute window and flags a wave when that window holds clearly more arrivals than were originally due then, with many of those flights running late. In other words, it looks for flights piling into the same hour, not just a normal busy hour.

Each wave gets a level of confidence:

  • Expected: most of the flights in the wave are already in the air, so the wave is very likely to land as shown.
  • Likely: many flights have not taken off yet, so the picture can still change.

PeakMere also watches for a big wave, which compares the number of travelers, not just flights, with what is usual for that weekday and hour. Because hub banks can move a little from day to day, this check allows some tolerance so a bank that lands slightly early or late is not mistaken for something unusual.

Finally, a landing now signal tells you when far more travelers than usual have landed in the last 30 minutes. That is the moment a wave is reaching the terminals, and the curb is about to get busy.

All of these are estimates. Flights can be delayed further, diverted or cancelled, and a wave can shrink or spread out as a result.

Turning a wave into curb time

The time a flight lands is not the time a traveler is ready for a ride. After landing, the plane taxis to the gate, people get off row by row, walk through the terminal, stop for bags and then open their app.

PeakMere's estimates:

TravelerUsually reaches the curb
Domesticabout 15 to 45 minutes after landing
Internationalabout 45 to 90 minutes after landing (passport control, customs, bags)

So if a domestic wave lands from 6 PM to 7 PM, ride requests from it are likely to spread from roughly 6:15 PM to 7:45 PM. An international wave in the same hour would reach the curb later, roughly 6:45 PM to 8:30 PM.

This is why arriving at the landing time is often too early, and arriving at the end of the curb window is often too late. The sweet spot is usually being in position as the curb window opens.

Big hubs vs airports where most travelers stay

Not every traveler in a wave becomes a rider. At big connecting hubs, many travelers are only changing planes and never leave the airport. A huge wave in the air can mean a much smaller wave at the curb.

Our estimates of how many arriving travelers end their trip at the airport:

  • Charlotte (CLT): roughly 35% end their trip here; the rest connect to another flight.
  • Atlanta (ATL): roughly 44% end their trip here, about 60,500 people on a typical day.
  • Denver (DEN): roughly 54%.
  • Orlando (MCO): roughly 94%, because most visitors come to stay.

At an airport like Orlando, nearly every arriving traveler is a potential rider, so a wave in the air is close to a wave at the curb. At Charlotte, roughly two out of three travelers in a wave stay inside to catch their next flight, so the curb can feel much calmer than the arrivals board suggests. When you judge a wave, think about who is on those planes, not just how many planes there are.

A practical playbook

Here is a simple way to work with waves, adapted to your own city and schedule:

  1. Check before you commit. Before heading to the airport, look at whether a wave is expected or only likely, and when its curb window starts.
  2. Time your arrival to the curb window. For a domestic wave, plan to be in position about 15 minutes after the first flights land. For international flights, plan later.
  3. Use the waiting area. Wait where the airport's signs and your platform's rules allow, rather than circling or stopping at the curb.
  4. Avoid joining at the tail end. If a wave has mostly landed and the queue is already long, joining it late can mean a long wait for the last few requests. A nearby city area or a different plan may use your time better.
  5. Watch for the wave after a ground stop. When a stop ends, the held flights land together later. That gap between the stop ending and the wave landing is a good time to finish a ride, eat or charge, then head back.
  6. Expect changes. Further delays can push a wave back or thin it out. Recheck live conditions before each move.
  7. Mind the late night. Nationally, about 13% of the day's arriving travelers land between 10 PM and 2 AM, so late waves are real. Only work them if you are rested.

This works for any kind of driver. A taxi driver or chauffeur waiting for a booked pickup can use the same timing to plan around traffic at the terminals.

Quick checklist

  • A wave is many more arrivals than usual, packed into about an hour.
  • Banks at hubs repeat most days; delay waves appear after weather, ground stops or slow mornings.
  • "Expected" means most flights are already in the air; "likely" can still change.
  • Add about 15 to 45 minutes after landing for domestic travelers, about 45 to 90 for international.
  • Get in position as the curb window opens, not at the landing time.
  • At big hubs, many travelers connect and never reach the curb.
  • Avoid joining a long queue at the end of a wave.
  • Recheck live conditions, take breaks and never drive tired.

PeakMere spots arrival waves early and can alert you before they land.